| category |
Input and output expansion module |
| Product name |
expansion unit |
Performance
specifications |
Applicable sequence |
FX1N, FX3G, FX2N, FX3U |
| quality |
0.85kg |
General
specifications |
ambient temperature |
0~55℃...when operating - 25~75℃...when saving |
| Relative humidity |
5～95% RH (no condensation allowed)・・・・・When operating |
| Vibration resistant |
When installing on DIN rail |
Piece amplitude: 0.035 mm 10 times in each direction of X, Y, and Z (a total of 80 minutes) each |
| Judgment criteria, based on IEC 61131-2 |
| When installing on DIN rail |
Acceleration: 4.9 m/s 2 10 times in each direction of X, Y and Z (80 minutes in total) |
| Judgment criteria, based on IEC 61131-2 |
| When installing directly |
Piece amplitude: 0.075 mm 10 times in each direction of X, Y, Z (a total of 80 minutes) each |
| Judgment criteria, based on IEC 61131-2 |
| When installing directly |
Acceleration: 9.8 m/s 2 10 times in each direction of X, Y and Z (80 minutes in total) |
| Judgment criteria, based on IEC 61131-2 |
| Shock proof |
147 m/s2 , action time 11 ms, sine half-wave pulse 3 times in each direction of X, Y, Z |
| Judgment criteria, based on IEC 61131-2 |
| Noise resistant |
Noise voltage, Vp 10,000-p, noise width 1μs, rising to one, period 30 ~ 100 Hz of the noise simulator |
| Withstand voltage |
Between power terminal (AC power supply) and ground terminal: AC 1500 V for 1 minute |
| Between DC 24V service power supply and input terminal (DC 24V) and ground terminal: AC 500 V for 1 minute |
| Between output terminal (torch transmission) and ground terminal: AC 1500 V for 1 minute |
| Insulation resistance |
Between each terminal and the ground terminal: DC 500 V high resistance meter above 5 MΩ |
| ground |
Type D grounding (ground resistance: 100Ω or less) |
| Ground, dedicated ground or shared ground, please. |
| Atmosphere of use |
Corrosive, flammable gases, but conductive dust (dust) are very unsafe |
| Use height |
Below 2000 meters |
| It cannot be used in a pressurized environment above atmospheric pressure. Possibility of malfunction. |
|
Power
Specifications
|
Rated voltage |
AC 100V～240V |
| Voltage allowable range |
AC 85V～264V |
| Rated frequency |
50/60Hz |
| Mains fuse |
250 VA 5 |
| Inrush current |
AC 100V: Maximum 40 A5 ms or less |
| AC 200V: Maximum 60 A5 ms or less |
| Consumption of electricity |
35 W |
| 24V service DC power supply |
DC 24V 460 mA or less |
| When the input and output expansion blocks are connected, the DC power supply 24V is consumed. |
|
Enter
specifications
|
Enter score |
24 o'clock |
| Enter the connection shape |
Removable terminal block (M) 3 screws |
| Input form |
heat sink |
| Input signal voltage |
DC 24V±10% |
| input resistance |
4.3 kΩ |
| Input signal current |
5mA/DC 24V |
| Input current ON sensitivity |
3.5mA or more |
| Input current OFF sensitivity |
Below 1.5 mA |
| Enter response time |
about 10 ms |
| Input signal form |
Wireless voltage solder joint input or NPN transistor open collector |
| Input circuit isolation |
Optocoupler insulation |
| Input action representation |
The LED on the panel lights up when the input is ON. |
|
Output
specifications
|
Output score |
24 o'clock |
| Output connection shape |
Removable terminal block (M) 3 screws |
| Output type/form |
relay |
| External power supply |
AC 250 V DC 30 V or less |
| maximum load |
Resistive load |
2 A / 1 point |
| Please see below for the total load current in the UK. |
| and output 4 points/Eng: 8 A or less |
| and output 8 points/Eng: 8 A or less |
| inductive load |
80VA |
| minimum load |
DC5V 2mA (reference value) |
| Response time |
Discount→ON |
about 10 ms |
| ON→Discount |
about 10 ms |
| circuit insulation |
mechanical insulation |
| Output action representation |
When the relay coil is energized, the LED on the panel lights up. |
