New Products

Mitsubishi module FX2N-48ER-D

Mitsubishi module FX2N-48ER-D function introduction:
1 Input and output expansion unit
2 Input and output 24:24, expansion is possible.
3 The power supply is built-in, and various input and output devices and special

Product Description

brand MITSUBISHI/Japan Mitsubishi
Origin category import

Mitsubishi module FX2N-48ER-D function introduction:
1 input and output expansion unit
2 input and output 24:24, expansion is possible.
3. The power supply is built-in, and various input and output devices and special additions are also added to the second half of the basic unit and the same extension unit Can connect.

Mitsubishi module FX2N-48ER-D other performance:

category			Input and output expansion
Product name			expansion unit
Performance specifications	Applicable sequence		FX3G, FX2N, FX3U
	quality		0.85kg
General specifications	ambient temperature		0 ~ 55℃·····When operating - 25～75℃·····When saving
	Relative humidity		5～95% RH (no condensation allowed)・・・・・When operating
	Vibration resistant	When installing on DIN rail	Piece amplitude: 0.035 mm 10 times in each direction of X, Y, and Z (a total of 80 minutes) each
			Judgment criteria, based on IEC 61131-2
		When installing on DIN rail	Acceleration: 4.9 m/s ² 10 times in each direction of X, Y and Z (80 minutes in total)
			Judgment criteria, based on IEC 61131-2
		When installing directly	Piece amplitude: 0.075 mm 10 times in each direction of X, Y, Z (a total of 80 minutes) each
			Judgment criteria, based on IEC 61131-2
		When installing directly	Acceleration: 9.8 m/s ² 10 times in each direction of X, Y and Z (80 minutes in total)
			Judgment criteria, based on IEC 61131-2
	Shock proof		147 m/s2 ^, action time 11 ms, sine half-wave pulse 3 times in each direction of X, Y, Z
			Judgment criteria, based on IEC 61131-2
	Noise resistant		Noise voltage, Vp 10,000-p, noise width 1μs, rising to one, period 30 ~ 100 Hz of the noise simulator
	Withstand voltage		Between power terminal (DC power supply) and ground terminal: AC 500 V for 1 minute
			Between input terminal (DC 24V) and ground terminal: AC 500 V for 1 minute
			Between output terminal (torch transmission) and ground terminal: AC 1500 V for 1 minute
	Insulation resistance		Between each terminal and the ground terminal: DC 500 V high resistance meter above 5 MΩ
	ground		Type D grounding (ground resistance: 100Ω or less)
			Ground, dedicated ground or shared ground, please.
	Atmosphere of use		Corrosive, flammable gases, but conductive dust (dust) are very unsafe
	Use height		Below 2000 meters
			It cannot be used in a pressurized environment above atmospheric pressure. Possibility of malfunction.
Power Specifications	Rated voltage		DC24V
	Voltage allowable range		+ 20%, - 30%
	Mains fuse		250 VA 5
	Consumption of electricity		30W
Enter specifications	Enter score		24 o'clock
	Enter the connection shape		Removable terminal block (M) 3 screws
	Input form		heat sink
	Input signal voltage		DC 24V + 20%, - 30%
	input resistance		4.3 kΩ
	Input signal current		5mA/DC 24V
	Input current ON sensitivity		3.5mA or more
	Input current OFF sensitivity		Below 1.5 mA
	Enter response time		about 10 ms
	Input signal form		Wireless voltage solder joint input or NPN transistor open collector
	Input circuit isolation		Optocoupler insulation
	Input action representation		The LED on the panel lights up when the input is ON.
Output specifications	Output score		24 o'clock
	Output connection shape		Removable terminal block (M) 3 screws
	Output type/form		relay
	External power supply		AC 250 V DC 30 V or less
	maximum load	Resistive load	2 A / 1 point
			Please see below for the total load current in the UK.
			and output 4 points/Eng: 8 A or less
			and output 8 points/Eng: 8 A or less
		inductive load	80VA
	minimum load		DC5V 2mA (reference value)
	Response time	Discount→ON	about 10 ms
		ON→Discount	about 10 ms
	circuit insulation		mechanical insulation
	Output action representation		When the relay coil is energized, the LED on the panel lights up.
	Output circuit structure